One of the most annoying problems you could face with bike brakes is bent and broken bike cables. This means that your brake might not provide well, which makes you lose control when riding. Good thing, you now can learn how to fix bike brakes cable properly. Before doing so though, it is important to note that it is dangerous to work on a broken cable system. Here are some simple steps you need to follow:

The first step is to ensure that the broken cable system is disconnected from the rest of the system. To do this, unhook the outer cable housing from the brake lever housing with a wrench. Make sure that the cable is fully detached from the housing before proceeding to the inner cable housing. Now, remove the outer cable housing and take out the broken inner cable housing from its socket. Now, line up the new inner cable housing with the previous one.

The second step is to reinstall the cable on the lever housing. Locate the brake pads and their corresponding cable lever housing in the same way. Ensure that the cable is fully extended to its full span, and secure it with new clamps or tie wraps. Hook the new inner cable housing into the lever housing with the help of new clamps. Hook the brake lever firmly and attach the cable caps back to its respective brake pads.

The next step is to align the break cable to its appropriate slot on the outer cable housing. Check the break cable for proper alignment by slowly pressing on it using both your thumbs and forefinger. Also ensure that the break is facing the right direction. You should also ensure that the break is perpendicular to the bike frame when you are attaching the outer cable housing to the lever.

The final step is to secure the break cable housing to its appropriate slot on the outer cable housing. Hook the new cable housing into the lever with the use of new cable housing clamps. Re-tighten the cable clamps and screw them securely into place. You should repeat this process until you get the desired level of resistance for the lever. Now, reconnect the inner cable housing to its corresponding slot on the hub.

These are some simple and quick tips for replacing your bicycle’s brake cables. These tips will ensure that your bike brake mechanisms works perfectly. However, if you are not confident about handling the task on your own, you could always take the help of professional bicycle mechanic to do it for you. They are the best persons who could do the job smoothly and effectively.

How to fix bike gears?

If you own a bike or intend to buy one in the near future, it is important for you to know how to fix bike gears. This way, you will know how to service your bike and avoid unexpected problems when riding on the road. Here are some basic things you need to know on how to fix bike gears.

Sometimes you need to change up or even down on a gear just to get your desired speed and distance and again back to where you started from to put your pedalation into reverse. In a worst case scenario, the chainsaw could derail away from the correct teeth of your gears, throwing you off the path and off course. Fortunately, you don’t need to be mechanical knowledgeable to easily fix other bicycle gears. All you need is a good knowledge about how to work with bicycles and the parts that make it run. Here’s a small guide on how to fix bike gears.

The first thing you should know is the basic idea behind how to change gears on your bike. Before starting your work, you should make sure that your rear wheel is fitted with a brake cable as well as a forward or reverse cable depending on how you would like to go. Using the correct cable tension as well as engaging the levers smoothly will make a big difference on how smoothly you can change gears while pedaling.

If your bike has a chain and a pedal, the cable should run under the seat and in between the pedals. With this kind of bike, it is important to check the cable tension as well as the housing that holds the shift gears. The housing is made out of a flexible metal and a quick change of the housing’s seat can sometimes cause the gear to jam. In order to avoid this from happening, you can slide the housing further back under the seat and tighten the nut that connects it to the housing.

Next in line is the shifter itself. This is also an important component to check as improper shifting can easily cause the bike to jump or slip. For a better illustration, imagine that the lever of the left foot is engaged while the right pedal is not yet engaged and if you then shift into the left gear, the levers inside the shift gear get pushed out of the housing thereby shifting gears.

Once you are done with this part, you should now focus on the other gears and the corresponding pedals. Keep in mind that when you are pedaling, the pedals and the gears should move smoothly with very little noise from any jostling. You can test this by cycling for about one minute without changing gears. If you feel that the gear shift moves smoothly and there is no delay in the chain from slipping, then you know that your shifter is working fine.